SANDWICH TECHNIQUE

Home Forums Adhesive dentistry SANDWICH TECHNIQUE

Welcome Dear Guest

To create a new topic please register on the forums. For help contact : discussdentistry@hotmail.com

Currently, there are 0 users and 1 guest visiting this topic.
Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • #9863
    Anonymous
    Online
    Topics: 0
    Replies: 1150
    Has thanked: 0 times
    Been thanked: 1 time

    Composite may not bond adequately to dentin, therefore during polymerisation, it may lead to formation of a gap at the cavity margin situated in dentin.This bond can be improved by placing GLASS IONOMER CEMENT lining between the composite and the dentin.This is called the sandwich technique.
    GIC bonds chemically to the tooth dentin and micromechanically to the composite.
    The GIC is etched for retention of the composite.Also the anti-cariogenic effect is beneficial.

    INDICATIONS:
    -Lesions where one or more margins are in dentin like cervical lesions.
    -Class II composite restorations.

    PROCEDURES:
    The dentinis conditioned and a thin layer of GIC liner cement is applied.The cement must be exposed at the margins to ensure fluoride release.
    Phosphoric acid is used to etch the enamel portion and also the lining GIC, to increase surface roughness.
    Light cured gic need not be etched.
    After adequate drying, bonding agent is applied to the cement surface and etched enamel.
    This is followed by the usual method of composite insertion.

    #14478
    tirath
    Offline
    Registered On: 31/10/2009
    Topics: 353
    Replies: 226
    Has thanked: 0 times
    Been thanked: 0 times

    Closed Sandwich technique: This technique is used when a glass
    ionomer is placed in an area where there is no contact with the cavosurface
    of the preparation. The material is completely covered with
    the restorative material. (Base and liners) A liner should be used as a
    very thin covering over deep and questionable dentin surfaces. A
    base should be selected anytime the material is placed thicker than
    .25 mm and should be a high strength restorative material. Tooth
    conditioning is not required with this technique.
    Open Sandwich technique: This technique is used when a Glass
    ionomer is placed in an area where there is contact with the cavosurface
    on the preparation. The margin of the preparation is sealed
    with the Glass Ionomer material. A restorative material should
    always be used here and the tooth conditioner is indicated.
    Class II Open Sandwich: Used when any part of the gingival
    margin of a Class II preparation has been extended past the CEJ and
    no longer has an enamel cavo-surface.
    1. After placement of the matrix, condition the gingival floor with GI
    conditioner for 10 seconds and wash off.
    2. Place either a pure glass ionomer or a resin modified glass
    ionomer interprox. to the start of enamel margins. Do not build
    interproximal or occlusal contact in this material. Make sure that
    there is a minimum of 2mm of the final restorative material above the
    Glass Ionomer to support the marginal ridge.
    3. Continue with step 4 with the above composite technique if final
    material is a composite restoration.

    #14479
    adwait
    Offline
    Registered On: 08/02/2010
    Topics: 3
    Replies: 6
    Has thanked: 0 times
    Been thanked: 0 times

    Although the sandwith technique has proved its utility and predictability in durable composite restoration , the time has changed so the techniques and material science ,which led to the fact that there is hardly any need to use glass ionomers as base before placing composite restorations.
    There is predictable bond between the dentin and the composites leading to successful restoration even in reversible pulpits situations … If bonded well and protocol followed ..

    #14480
    Anonymous

    i agree, however the gic not just helps in bonding but mainly pulp protection…..few modified light cure dycal is available which can be used as pulp protection

    #14481
    adwait
    Offline
    Registered On: 08/02/2010
    Topics: 3
    Replies: 6
    Has thanked: 0 times
    Been thanked: 0 times

    What about the polyacrylic acid from gic which is more irritating to pulp than the shrinkage in composites..
    Why to use so many dissimilar material rather than using single material creating good integrated bond.. when the science and innovations permits and allow us to use materials /composites in predictable way.

    #14482
    sushantpatel_doc
    Offline
    Registered On: 30/11/2009
    Topics: 510
    Replies: 666
    Has thanked: 0 times
    Been thanked: 0 times

    Etching for composite in a deep cavity without an appropriate base can cause sensitivity and irritation…Researchers say that the polyacrylic acid molecules in GIC are too large to enter the pulp through the dentinal tubules..

    #14483
    Anonymous

    I agree,….gic isnt irritating to the pulp which is a noted fact

Viewing 7 posts - 1 through 7 (of 7 total)
  • You must be logged in to reply to this topic.