Ergonomic positioning

[Anonymous]

PATIENT POSITIONING SEQUENCE: UPPER ARCH
After the operator and assistant stools are properly adjusted, the patient must be positioned properly depending upon the quadrant and tooth surface being treated. For the upper arch, follow these general guidelines.
1. First, recline the patient to a fully supine position. This can be challenging for some patients who resist reclining due to postural hypotension, inner ear issues, vertigo, and a myriad of other conditions. However, this is oftentimes of a psychological origin. In these cases, try positioning the chair already partly reclined before the patient arrives. In this way, when the chair is fully reclined, it will not feel as dramatic to the patient. Another strategy is to meet them halfway—recline them slightly further than you actually need them reclined, then if they protest, say that you’ll meet them “halfway.” Placing a TV, mobiles, or other distractions on the ceiling can also go a long way in helping to get the patient more comfortable while supine.
2. Always ask the patient to scoot to the end of the headrest. This is especially important if using a flat headrest—reaching or leaning over the “dead” headrest space can lead to a myriad of musculoskeletal dysfunctions. Oftentimes, this is not done in deference to patient comfort—their spinal curves may not align properly with the patient chair support when scooted up all the way to the end of a headrest. This is easily resolved with dental ergonomic cushions that support the patient’s neck, lower back and knees .
3. Adjust the head tilt appropriately for the upper arch, angling the double articulating headrest up into the patient’s occiput. This will not only enable better viewing of the oral cavity, but also help relax the patient’s cervical muscles. The occlusal plane of the upper jaw should be tilted backward up to 25° in relation to the vertical plane. You can check for proper positioning from the side, using an instrument handle to visualize the angle of the occlusal plane. Cervical support cushions can greatly aid in attaining this position. Position the larger end under the neck for maxillary procedures and reverse the cushion for mandibular treatment.
4. Adjust the height of the patient chair so the dentist’s forearms are parallel to the floor or sloping 10° upward. Another guideline is to position the occlusal surface at elbow level or slightly higher while operating. If positioning the patient above elbow level, armrests should be considered. The patient’s height may also be determined proprioceptively by closing the eyes and slowly moving the arms up and down until a comfortable working position is attained.Once the proper height is attained, position the patient chair accordingly.
5. Rotate and/or side-bend the patient’s head to view the treatment area. Rotation is best achieved with verbal cues, while side-bending can be performed manually. Move into a clock position that establishes a line of view that is perpendicular to the tooth surface being treated. This may be direct or indirect, depending upon the tooth surface being treated. Mirrors should be used whenever direct viewing of the oral cavity requires leaving neutral posture. One study revealed that more dentists who use a mirror are pain-free than those who do not utilize a mirror.

Lighting should parallel the operator’s line of sight as closely as possible to prevent shadowing. Overhead versus head-mounted light shown. Head-mounted lighting will cause the least shadowing.

Figure 5. To enable a direct line of sight that is perpendicular to the lingual of No. 19, the operator moves to the 9 o’clock position.
Figure 6. The occlusal plane of the lower arch should be angled 30° to 40° above the horizontal plane when treating molars and premolars.

For example, when treating the occlusal of tooth No. 3, the dentist should be in the 11 o’clock to 12 o’clock position to enable an indirect line of sight perpendicular to the tooth surface. In general, the 11 o’clock to 1 o’clock positions enable some of the most neutral operator postures, especially of the arms, and should be made easily accessible in the operatory.Frequent positioning at the 10 o’clock position without a mirror tends to encourage more arm abduction and neck/ shoulder problems.
7. Position the tray and delivery system within easy reach. Handpieces and instruments should be at about elbow level. Over-the-patient delivery systems should not cause upward reaching.
8. Identify nearby inter- or extraoral finger fulcrums that enable you to relax the hand and arm.
9. Direct the overhead light to prevent shadowing. The light should parallel the operator’s line of sight to within 15°. Thus, the light will be placed slightly behind and to one side of the operator’s head. A head-mounted light will parallel even more closely with the operator’s line of sight to prevent shadowing. The assistant’s thighs should be angled toward the head of the patient, so assistant’s left hip is at patient’s left shoulder. The knees should preferably be interlocking with the dentist to gain the closest, safest positioning and posture. While this assistant positioning is a common practice in Europe, many dentists in the United States are uncomfortable with physically contacting the assistant’s leg.
The assistant may also need to adjust the stool position, depending upon the arch being treated—the stool may need to be slightly raised to visualize the lower arch. The assistant’s delivery system should be over the lap for easy retrieval of instruments/utilities.

PATIENT-POSITIONING SEQUENCE: LOWER ARCH
1. First, recline the patient to a semi-supine position. This will be only 20° elevated from the horizontal supine position. A common mistake is to position the patient halfway between supine and a full-upright posture for lower arch, which can make visualizing the oral cavity a postural challenge.
2. Adjust the headrest forward, so the patient’s chin tilts downward and the occlusal plane of the lower jaw is close to horizontal when the dentist is working in the 9 o’clock to 10 o’clock position. Reversing the position of a dental cushion will help in attaining this position (Figure 3b). The head will need to be tilted further back when treating anterior teeth of the lower jaw and further still when treating the lower molars and premolars.
3. Adjust the height of the patient chair so forearms are parallel to the floor or sloping 10° upward. The height of the patient chair when treating the mandibular arch will need to be lower than when treating the maxillary arch. Some patient chairs do not adjust low enough for shorter dentists to attain a safe, relaxed arm posture in the semisupine position. A saddle stool can greatly aid in solving this problem, since it positions the dentist higher—halfway between standing and sitting.
4. Adjust the patient’s head position: Rotate the patient’s head to view the treatment area.
The operator must then be positioned correctly depending upon the tooth surface being treated.
5. Move into a clock position that establishes a line of view that is perpendicular to the lingual surface being treated. This may be direct or indirect, depending upon the tooth surface being treated.
When treating the anterior teeth, molars or premolars of the lower jaw, an 11 o’clock to 12 o’clock position may be used. For anterior lower teeth, the lower jaw should be angled backward about 30°. Tilt the headrest slightly backward or use the large end of the dental cushion to slightly elevate the chin.
6. Guidelines for positioning the tray, delivery system and lighting are similar to those for the upper arch.
When treating the lower arch, it is an excellent opportunity for a short- to medium-height assistant to stand. The assistant must stand very close to the patient to avoid leaning and reaching forward with the arms.

        

[Author]

Posts